Guaranteeing the highest quality products has always been our pursuit

Copper Castings For Commercial Vehicles

  • Copper Castings For Commercial Vehicles
  • Copper Castings For Commercial Vehicles
Copper Castings For Commercial Vehicles
  • Yaojia
  • china
  • 25 days
  • 3 Million Tons

Yaojia Trading delivers precision copper alloy castings designed to meet the rigorous demands of commercial vehicle applications.

Copper Alloy Castings for Commercial Vehicles – Built for the Road

One problem we hear from commercial vehicle OEMs and fleet operators

A‍‌‍‍‌ commercial vehicle doesn't spend a lot of time troubleshooting component issues. Since most transportation vehicles like trucks, buses trailers operate 24/7 on the road - under varying loads, vibration, heat and being continuously exposed to water, road salt, or operating fluids - a minor wear part getting broken or a fluid-control part malfunctioning can cause more than just the price for the replacable part. In addition to these, the workshop time cost vehicle downtime, the loss from interruption of the delivery schedule, etc.

Commercial vehicle manufacturers, fleet service supervisors, and aftermarket vendors tell us similar stories. In cases where common steels, aluminum, or cast irons do not offer the ideal combination of properties, copper alloy castings are a good choice.

The Yaojia approach:

Making castings that are not only custom in copper alloy but also designed for the rough road conditions is another part of the Yaojia approach.

Casting is our specialty; machining, inspection, finishing, if required by project, will go smoothly together as we can do it ourselves.

It's not a regular component. It’s a piece of gear that is designed to work on the ‍‌‍‍‌road.

Commercial Vehicle

Technical specifications

ParameterTypical capability / specification
Available copper alloysC83600, C90300, C95500, CuNi1.5Si, and other customer-specified alloys
Tensile strengthTypically 300–650 MPa, depending on alloy and condition
Yield strengthTypically 150–450 MPa, depending on alloy and condition
ElongationTypically 10–25%, depending on alloy and casting condition
Electrical conductivityApproximately 18–45% IACS for selected grades
Thermal conductivityApproximately 45–120 W/(m·K), alloy dependent
Casting processesSand casting, centrifugal casting, investment casting
Maximum part sizeUp to approximately 500mm in length and 300mm in width
Surface roughnessAs-cast Ra 6.3–12.5μm; machined Ra 1.6–3.2μm
Pressure testingHydraulic or pneumatic testing available when required


Brass castings in commercial vehicles - applications


The wear and bearings parts

Bearings, bearing components, wearing sleeves, guide parts, wearing plates, and thrust parts
Cooling and thermal-control parts

Thermal-control parts, heat-transfer parts, cooling-system hardware, thermostat parts, custom thermal-control fittings

Electrical and connector parts
Electrical connector parts, conductive supports, component connection parts, grounding, current-carrying parts,
Steering, suspension, and other moving assemblies

Bearings, bearing components, wear plates, guide parts, support components, and high-contact-wear parts


Copper-based alloys for commercial vehicles - why?


Depending on the alloy, copper-based materials are able to offer

  • Wear resistance of moving parts

  • Resistance to corrosion in road salt and operating fluids

  • The thermal performance for heat management

  • The electrical conductance for connection parts

  • Good machine properties for fine details

  • Excellent performance in sliding and spinning parts

Choice of material should focus on functionality of the part and not be treated as just another standard choice.

Quality control — our 5-step inspection process

For commercial vehicle copper alloy castings, quality control is built into every stage of production. We follow a structured inspection process that ensures every part meets drawing requirements before it ships.

StepInspection stageWhat we checkMethodControl standard
1Incoming material verificationMaterial grade, dimensionsSpectrometer, micrometer100% traceability; dimensions within tolerance
2First-article inspectionFull dimensional check on first castingCMM, thread gauges, hardness testerAll features per drawing
3In-process inspectionCritical dimensions, casting qualitySampling, visual inspectionKey features checked per control plan
4Final dimensional inspectionFull dimension check on finished partCMM, profilometer, hardness tester100% critical dimensions verified
5Final visual & documentation reviewSurface finish, coating, packagingVisual inspectionZero defects; all documentation complete

Key inspection equipment: CMM, hardness tester, spectrometer, pressure test equipment, visual inspection stations

What we deliver: Material certificates, dimensional reports, CMM data, hardness test results, pressure test reports, full traceability


Casting and machining are used when the assembly needs it

  • Ready cast parts

  • Roughly made parts

  • Entirely finished parts

  • Holes drilled and tapped

  • Fins are bored out

  • Dimensional accuracy for sealing

  • Completed part interfaces

If a part is being cast and machined within one production unit, communication problems between departments can be avoided — the dimensional requirements are examined together before the product is made.

Purchase process and delivery


Sending the following documents will help us quote you a price:

  • 2D drawings, 3D CAD models, and prototypes

  • Material type and grade

  • Number of items required

  • Machine details and surface finish requirements, if applicable

  • Documentation or certification requirements

  • Customer's delivery time

MOQ: We accept minimum order quantities as low as 50 units for regular production. Prototype amounts and small-volume product runs can be considered if needed.

Payment: We require 30% upfront; the remaining balance is to be paid upon confirmation of inspection video - this is the method of payment (T/T).

Different shipping modes: Full container load (FCL) and Less than Container Load (LCL) shipment options are available to our customers. In order to protect against shipping-related damages, we offer our customers protective packaging and reinforced cartons as options.

Turning over a product: Regular production: 15-25 working days. Special shapes or materials: 25-40 working days. The exact time frame is made clear at the time of the order. We also confirm that.


Warranty

We‍‌‍‍‌ are responsible for 12 months from the time of delivery. If a part fails due to manufacturing defects like - Casting defect, machining error, wrong materials - we replace the part or give credit. Wear parts, broken impact part or modified ones from delivery? Not covered.

We give straight answers whether the warranty is applicable or not.

For making claims, you can send us images of the part, the part number, and the order number. After that we will respond within 48 hours.

If a production batch is faulty, we remould the batch keeping all the standards in the original work same, like drawing, material and tolerance.

If you have any questions? About materials, specifications, machining instructions, drawings, etc., we directly respond to you. Never a dead ‍‌‍‍‌end.

Casting With Copper

About Yaojia Trading

Luoyang Yaojia Trading Co., Ltd. has over 20 years of practical experience in casting and metal component manufacturing. The company was founded by Mr. Xi Xianmin, who has more than 25 years of experience in foundry production and engineering management.

Our capabilities:

  • 18,000m² modern production base

  • ~68 employees

  • 16-person R&D team with two senior engineers

  • Annual casting and machining capacity:15,000 tons 

  • IATF 16949 quality management certification

Integrated services:

  • Copper alloy casting (sand, centrifugal, investment)

  • Multi-axis CNC machining

  • Heat treatment

  • Surface treatment and coating

  • Inspection and CMM

  • Pressure testing

  • Supply-chain coordination

Customers & markets:

Commercial Vehicle

  • Tier 1 supplier to BYD, Chery, Great Wall Motors

  • Commercial vehicle OEM supply

  • Aftermarket replacement parts

  • Products exported to South Korea, Japan, USA, Australia, Germany

Exhibition

In May 2024, Yaojia Trading exhibited at the China International Foundry Technology and Equipment Exhibition in Shanghai, showcasing casting accuracy and comprehensive industry-chain service capabilities.

Casting With Copper

FAQ

Q1: What types of brass can be used for commercial vehicle components in casting form?

The available materials are C83600, C90300, C95500, CuNi1.5Si, as well as customized alloys requested by the clients. The selection of one is decided based on how it will behave mechanically, in terms of wear, thermal, electrical, and resistance to corrosion.


Q2: Can you produce castings from OEM drawings?

Of course, we can. Drawings, CAD files, technical drawings, or even samples can serve as the first reference point.


Q3: Is it possible to machine brass castings after being cast?

We can do that. We can supply either ready-as-cast, rough-machined or fully machined parts.


Q4: Do you make wear bushings and bearing parts?

Absolutely. Wear resistances, bushings and sleeve components along with others belonging to bearing-related parts are all in the category of our product line.


Q5: Can you offer support for prototype development and small batch manufacturing?

We can! For sample prototype testing, validation parts, small volume pilot runs, as well as pilot batch production we offer support.


Q6: How will you decide on the material?

Various factors such as load, temperature, friction, lubrication, corrosion, conductivity and service life are considered prior to a final decision on an alloy.


Q7: Which quality assurance documents can I request?

We have various material documentation records such as certificates, chemical analysis, mechanical test, dimensional checks, reports from CMM, pressure-test data, and tracing documents.


Q8: Is there a way to test for leaks or integrity?

Sure! When pressure integrity is specified, hydraulic and pneumatic leak testing can be arranged.


Q9: What typical manufacturing time period do you have?

It's 15-25 working days for a standard part, whereas a complex component needs 25-40 working days at an average. This lead time can be discussed and will be confirmed once a new order is placed.


Q10: Do you require any purchase amount?

Minimum for mass production: 50 units. Prototypes or small orders: subject to negotiation.


Q11: How many units can you produce per year?

We are capable of producing 15,000 metric tons annually, covering both casting and CNC services.


Q12: Which certifications are you holding with respect to quality and standard compliance?

We are IATF 16949 certified! We provide Tier 1 components not only to our Chinese clients BYD, Chery, and Great Wall motors but also ‍‌‍‍‌overseas.


Four questions to ask any commercial vehicle copper alloy casting supplier

  1. What copper alloys do you recommend for wear and bearing applications?

  2. Can you supply both castings and fully machined finished parts?

  3. What inspection and material certification do you provide?

  4. Do you have experience with similar commercial vehicle components?

We have answers ready. Ask us.


Get the latest price? We'll respond as soon as possible(within 12 hours)

Privacy policy

close left right